Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Check vehicle fitment
Porsche
9965725
Product Information
The Porsche Cover Cap for Plenum Chamber Cover is a genuine OEM finishing piece designed to secure and complete the plenum chamber area beneath the windshield. Finished in black, these caps neatly close off the ends of the plenum chamber cover, preventing debris and moisture from entering while preserving the clean, factory look of your Porsche.
Fits:
What This Product Does:
Why Replacement Matters:
Diagram Ref No 9
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
9965725
The product you are viewing cross references to these numbers
Product Information
Cover Cap For Plenum Chamber Cover, Black.The Porsche Cover Cap for Plenum Chamber Cover is a genuine OEM finishing piece designed to secure and complete the plenum chamber area beneath the windshield. Finished in black, these caps neatly close off the ends of the plenum chamber cover, preventing debris and moisture from entering while preserving the clean, factory look of your Porsche.
Fits:
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
What This Product Does:
- They act as end caps / cover caps on the cowl / plenum / windscreen base / vent grille area, covering the ends of the trim or grille to provide a finished look.
- They help prevent water, debris or dirt ingress into the cowl / dash vent cavities by sealing off the open edges where grille meets body.
- They provide aesthetic finish and protection to fasteners, edges or joints in the cowl / plenum area.
- The cap is broken, cracked, faded, or missing, leaving the edge exposed.
- You see visible fasteners, rough edges or openings at the cowl edge / grille.
- You notice water ingress, dirt or debris entering behind the grille or cowl area (especially in rain or car washes).
- The appearance is inconsistent (one side has cap, the other doesn’t) — visually unbalanced.
Why Replacement Matters:
- Restores a clean, factory-finished appearance to the cowl / grille area.
- Helps keep out water and debris, protecting the underside of the cowl, vent passages, and interior of the dash.
- Prevents rust, corrosion or wear to components under the cowl that might be exposed if edges are open.
- A small, low-cost part, but gives a big touch to visual completeness and protection.
Diagram Ref No 9
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
9965725
9965725690101C
9965725700101C
The product you are viewing cross references to these numbers
Vehicle Group
Vehicle Group
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
Select Below
Prices from: £5.63
