bracket Genuine Porsche part 99950763500

Metal Clamp for Front Axle C2 Tray
This original Porsche retaining clamp is used to secure the front undertray / front axle tray panel, helping keep the underbody covering correctly mounted and aligned.
Sold individually

Fits:
Porsche 986 Boxster 1997 - 2004
Porsche 996 Carrera 1998 - 2005
Porsche 996 GT3 1999 - 2005
Porsche 996 Turbo 2001 - 2005

Diagram ref no 3

This clamp is used in the front axle tray / underbody protection panel mounting system on selected Porsche 986 and 996 models.

What This Part Does / Functions
•  Secures the front axle C2 tray / undertray panel
•  Helps hold the underbody protective covering in place
•  Maintains correct undertray alignment and fitment
•  Helps prevent tray movement, vibration or rattling
•  Replaces a missing, corroded, bent or damaged original clamp
•  Supports correct reassembly after undertray removal
•  Provides OE Porsche metal clamp fitment and durability
•  Helps maintain the factory underbody panel mounting arrangement.

Why Replace This Part?
Undertray clamps are exposed to road spray, salt, dirt, heat, vibration and repeated removal during servicing. Over time, the clamp can corrode, bend, weaken or go missing. A missing or damaged clamp may allow the front axle tray to sit loose, rattle, sag or detach from its correct mounting position. Replacing it with an OE Genuine Porsche metal clamp helps restore secure undertray fitment and keeps the front underbody protection panel correctly fastened.

Common Symptoms of a Missing or Damaged Clamp
•   Loose front undertray or axle tray
•   Rattling or vibration from the front underbody area
•   Undertray panel not sitting flush
•   Missing clamp after previous service work
•   Corroded or bent clamp hardware
•   Underbody cover movement at speed
•   Poor alignment of the C2 tray panel
•   Damaged fixing point during undertray removal.

When to Replace This Part
•   When refitting the front axle tray / C2 tray
•   If the original clamp is missing, corroded, bent or damaged
•   During front undertray or underbody panel replacement
•   After front-end or underside impact damage
•   During routine servicing if undertray hardware is worn
•   When replacing broken or incorrect retaining clips
•  During restoration of the front underbody panel system

Where It Fits on the Car
This clamp fits in the front underbody / front axle tray area. It is used to retain the front axle C2 tray / underbody protective covering to the vehicle’s front underside mounting points.

Correct positioning is important to ensure the tray sits securely and does not rattle or move while driving.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99950765709

The product you are viewing cross references to these numbers

U-clip for side sill trims. Sold as EACH



Fits:
Porsche 996 Carrera 4 (10pcs per car)
Porsche 996 Carrera with Aerokit (18pcs per car)
Porsche 996 Turbo (10pcs per car)
Porsche 996 GT3 (18pcs per car)

Porsche 997.1 Carrera 4 (18pcs per car)
Porsche 997 Turbo / GT3 (18pcs per car)

Porsche 997.2 Carrera  (18pcs per car)
Porsche 997.2 Turbo / GT3 (18pcs per car)

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99950764009

The product you are viewing cross references to these numbers

U-Clamp For Front / Rear Bumper.

The Porsche Genuine OE U-Clip is a factory metal retaining clip (also known as a U-clip, speed clip, or retainer clip) used across a wide range of Porsche models. It is primarily used in front and rear bumper assemblies, as well as associated trim and grille fixings.
This versatile clip is designed to provide a secure fastening point for screws and panels, ensuring proper alignment and retention of exterior body components.

Widely Used Across Multiple Porsche Model Ranges, Including:

• Porsche 911 (996 / 997 / 991)
• Porsche Boxster / Cayman (986 / 987 / 981 / 718)
• Porsche Turbo / GT models (Various Applications)

What This Product Does:
The U-clip slides over body panels or brackets and provides a threaded fixing point for screws or bolts. It is commonly used to secure:

• Front and rear bumpers
• Bumper linings and trims
• Air ducts and grilles
• Heat shields and covers

By holding panels firmly in place, it ensures correct fitment, reduces vibration, and allows easy assembly and removal.

Fitment – Position on Car:

Fitting position:

• Exterior body / trim

Location:

• Front bumper assemblies
• Rear bumper assemblies
• Grilles, ducts, trims, and covers

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99950769600

The product you are viewing cross references to these numbers

Metal Clamp for Front Axle C2 Tray
OE Match metal clamp for the front axle C2 tray on Porsche 986 Boxster and 996 models. This replacement clamp helps secure the front axle tray or underbody panel correctly, supporting stable fitment and original-style underbody protection.
Sold individually

Fits:
Porsche 986 Boxster 1997 - 2004
Porsche 996 Carrera 1998 - 2005
Porsche 996 GT3 1999 - 2005
Porsche 996 Turbo 2001 - 2005

Diagram ref no 3

The metal clamp helps hold the front axle tray securely in position. Correctly fitted underbody tray hardware helps prevent rattling, looseness, panel movement, and damage to the tray or surrounding mounting points.

Functions
•  Replaces the front axle C2 tray metal clamp
•  Helps secure the front axle tray or underbody panel
•  Supports correct underbody panel alignment
•  Helps reduce rattling, vibration, and loose panel movement
•  Suitable for front tray removal, refit, repair, or restoration
•  Helps maintain original-style underbody fitment
•  OE Match replacement for Porsche underbody fixing repair.

Why Replace This Part?
Underbody fixing clamps can become corroded, bent, worn, missing, or damaged during servicing, accident repair, tray removal, or general underbody maintenance. A damaged or missing clamp may allow the tray to sit incorrectly, rattle, loosen, or detach from its mounting position. Replacing the clamp helps restore secure front axle tray fitment.

When to Replace This Part
•  Front axle tray clamp is missing, corroded, bent, or damaged
•  Front axle tray or underbody panel is loose
•  Underbody panel rattling or vibration is present
•  Tray has been removed for service or repair
•  Front underbody fixings are being refreshed
•  Accident repair or bodywork is being carried out
•  The vehicle is undergoing Porsche 986 Boxster or 996 restoration

Where it fits on the car
This clamp fits at the front axle C2 tray / front underbody tray mounting area on Porsche 986 Boxster and 996 models.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99950765709

The product you are viewing cross references to these numbers