顶部安装套件密封外倾板适用于保时捷 997 2WD  ❭  SUSPENSIONKIT09

Rennline Sealed Front Camber Plates.
SET OF 2

Fits:
Porsche 997 C2 / C2S 2005-08 (2 Wheel Drive)
Porsche 997 C2 / C2S 2009-12 (2 Wheel Drive)
Porsche 987 Boxster MKI & MKII 2005-12
Porsche 987C Cayman MKI & MKII 2005-12

Under extreme conditions, such as road racing and autocross, negative camber is required to keep as much of the tire's contact patch on the road as possible. Stock suspension mounts will not allow you to achieve the necessary amount of negative camber required for this type of performance driving. Rennline's sealed camber plates incorporate FK motorsports spherical bearings and eliminate the indistinct feedback associated with factory rubber mounts. Comes as a set of two. Why are Rennline's strut mounts the best ?

* Drastically increased bearing life due to the integrated factory GT3 weather seals.
* FK Motorsport Teflon-lined spherical bearings.
* Rigid bearing mount, not clipped in like some products available.
* Specially machined upper nut to allow clearance for maximum negative camber settings.
* Allows for up to 1.25 degrees of added negative camber.
* Special tool included to hold strut shaft from turning when tightening upper nut.
* Can be used with all factory and aftermarket struts, Including factory non adjustable units.
* Webbed machined base for light weight and superior strength.
* Fully rebuildable
* CNC machined 6061 anodized aluminum construction with stainless steel hardware.


Note: When using factory non adjustable struts with factory spring seats, weather seal must be remove

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

S21

您正在查看的产品与这些编号存在交叉引用关系

QuickChange™ Camber Plates.
Sold per kit, 1 kit req'd per car.



Elephant Racing's QuickChange™ Camber plates offer true ease of adjustment. The "slider" design allows a full range of adjustment without the need for removing and rotating the plate for C2, C4, and Turbo models.

Fits:
Porsche 996/997 C4 and Turbo Models 1999-2012

More Camber
Range of adjustment is extreme, with 19mm of added travel. This delivers over 2 degrees of added camber, allowing even DOT-R tires and slicks to produce maximum grip.

QuickChange Camber Plate for C4 and Turbo Models
The Quickchange camber plates are available for C2, C4 and Turbo models and work with stock-type springs and coilovers. They will not raise ride height when used with stock-type springs.

Higher Performance
Spherical bearings further improve performance. The spherical bearings pivot freely, but eliminate the deflection that is inherent with the factory rubber bushings. This is important for two reasons;

– The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.

– The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.

Fully Weather Sealed
The included spherical bearings are oversized, maintenance-free, and PTFE lined – they never need lubrication.
Integrated weather seals on both bottom and top of the spherical bearing extend bearing life. Dirt and water enter competing non-sealed products to accelerate bearing wear. Worse yet are bottom-only seals that can actually trap water that enters the open bearing top!

Our weather seals are fully compatible with coilovers and stock type springs.

Use Stock Springs or Coilovers
Fully compatible with stock springs and aftermarket lowering springs. Also supports coilovers that use and upper spring perch.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2152210

您正在查看的产品与这些编号存在交叉引用关系