Original Porsche Part 原装 Porsche 零部件 91133310208

轻量化空心后扭杆。（一套2根）

适用：
保时捷 911 65-86 后部

共有7种尺寸可供选择：

- 25毫米
- 26毫米

- 27毫米

- 28毫米
- 29毫米
- 31毫米
- 33毫米

使用这些高精度、轻量化的空心扭杆来加强您的悬挂系统。

采用航空级 4130 铬钼钢制造，并经过热处理，具有高强度和可靠性。

镀锌，两端封堵，具有优异的耐腐蚀性。

精密加工的花键端，完美契合。

无中心研磨和枪钻加工，以实现一致的弹簧刚度。

与同等刚度的实心杆相比，重量更轻。每根杆最多可轻3磅！

这些是市面上品质最高的能量棒。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

1S166911R

您正在查看的产品与这些编号存在交叉引用关系

QuickChange™ 扭力杆，后部
按套件出售，每辆车需要 1 套。

#大象赛跑#

適用於:
适用于G50变速箱
保时捷 911 / 930 1987-89

QuickChange 扭力杆经过镀层和堵塞，并包括一个内螺纹端，您可以将其与螺栓接合以用作手柄，以便于提取/插入。

将后杆与我们的 QuickChange™ 弹簧板产品结合使用，可快速更换和重新索引扭力杆。无需拆除任何螺栓，即可通过 QuickChange™ 弹簧板抽出 QuickChange™ 扭力杆。对齐设置保持不变。您甚至不需要从汽车上拆下车轮。更换扭力杆每侧只需 5 分钟！

QuickChange™ 插入件可单独购买，用于转换您现有的空心扭力杆。

QuickChange™ 扭力杆可以轻松移除卡住的杆，因此即使在前部使用并配合工厂弹簧板使用也能带来好处（工厂弹簧不允许在不拆下弹簧板的情况下拔出杆）。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

21021

您正在查看的产品与这些编号存在交叉引用关系

QuickChange™ Torsion Bars, REAR
Sold per kit, 1 kit req'd per car.



Fits:
Porsche 911/912/930/914 '65-'86
Porsche 356 A/B '48-'65 (Pre-A, C and CS Read Notes),
Porsche 944/968/924 '76-'95 w/ QuickChange Spring Plates

PLEASE NOTE: sizes 34mm and 36mm are not applicable for 944, 968 and 924 models)

QuickChange Torsion Bars are Plated & Plugged and include a female threaded end that you can engage with a bolt to use as a handle for easier extraction / insertion.

Use the rears bars in combination with our QuickChange™ Spring Plate products for fast torsion bar swapping and re-indexing. QuickChange™ Torsion Bars can be extracted through the QuickChange™ Spring Plate without removing any bolts. Alignment settings are maintained. You don't even need to remove the wheel from the car. Changing torsion bars is a 5 minute per side operation!

A QuickChange™ Insert is available separately for converting your existing hollow torsion bars.

QuickChange™ Torsion Bars make it easy to dislodge a stuck bar, and thereby offer benefits even when used on the front and with factory spring plates (factory spring do not allow the bars to be extracted without removing the plates).

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

21020

您正在查看的产品与这些编号存在交叉引用关系

Plated & Plugged Hollow Torsion Bars. - REAR
Plated/Plugged 27mm, PAIR



Fits:
Porsche 911/912/930 1965-86
Porsche 356 A / 356 B / 356 Pre-A, C And CS Read Notes* (1948-65)

Our Plated & Plugged Hollow torsion bars are the best available. The ends are plugged to prevent moisture entry that rots ordinary hollow bars from the inside out. The entire bar is zinc plated for superior protection.

Excellent quality control means proper spline fit and spring-rate consistency bar-to-bar. Inferior quality competing bars fail on all counts.

• Hollow, light weight
• Plated & Plugged
• Consistent spring rate
• Great spline fit

Upgrade Hollow bars provide a nice weight savings over equivalent spring rate solid bars, especially true of the heavier rear bars. This is a great way to trim extra pounds from the back of your car.

* The size given is a solid-bar-equivalent. Actual hollow bar measures about. 5mm larger.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

1-PP911R27

您正在查看的产品与这些编号存在交叉引用关系

Plated & Plugged Hollow Torsion Bars - REAR
Plated/Plugged 29mm, PAIR



Fits:
For G50 Transmission
Porsche 911/912/930 1987-89


Our Plated & Plugged Hollow torsion bars are the best available. The ends are plugged to prevent moisture entry that rots ordinary hollow bars from the inside out. The entire bar is zinc plated for superior protection.

Excellent quality control means proper spline fit and spring-rate consistency bar-to-bar. Inferior quality competing bars fail on all counts.

• Hollow, light weight
• Plated & Plugged
• Consistent spring rate
• Great spline fit

Upgrade Hollow bars provide a nice weight savings over equivalent spring rate solid bars, especially true of the heavier rear bars. This is a great way to trim extra pounds from the back of your car.

* The size given is a solid-bar-equivalent. Actual hollow bar measures about. 5mm larger.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

1-PP911RT29

您正在查看的产品与这些编号存在交叉引用关系

Plated & Plugged Hollow Torsion Bars.
Plated/Plugged 26mm, PAIR



Fits:
Porsche 911/912/930 1965-86
Porsche 356 A / 356 B / 356 Pre-A, C And CS Read Notes* (1948-65)

Our Plated & Plugged Hollow torsion bars are the best available. The ends are plugged to prevent moisture entry that rots ordinary hollow bars from the inside out. The entire bar is zinc plated for superior protection.

Excellent quality control means proper spline fit and spring-rate consistency bar-to-bar. Inferior quality competing bars fail on all counts.

• Hollow, light weight
• Plated & Plugged
• Consistent spring rate
• Great spline fit

Upgrade Hollow bars provide a nice weight savings over equivalent spring rate solid bars, especially true of the heavier rear bars. This is a great way to trim extra pounds from the back of your car.

* The size given is a solid-bar-equivalent. Actual hollow bar measures about. 5mm larger.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

1-PP911R26

您正在查看的产品与这些编号存在交叉引用关系

Torsion bar, 24.1mm.



Fits:

Porsche 911 G-Model 1978-83
Porsche 911 Carrera 1984-85

Click 'Zoom in' for large parts diagram.
Diagram ref no 34

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91133310

您正在查看的产品与这些编号存在交叉引用关系

Torsion bar, 25 mm. (40/44 teeth).



Fits:
Porsche 911 Carrera 1986

Click 'Zoom in' for large parts diagram.
Diagram ref no 28

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91133310

您正在查看的产品与这些编号存在交叉引用关系

Torsion bar,  26 mm.



Fits:
Porsche 911 Turbo 1975-88

Click 'Zoom in' for large parts diagram.
Diagram ref no 28

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91133310

您正在查看的产品与这些编号存在交叉引用关系