专业工具

Oil return tube o-ring installer for Porsche 911



With this high-quality anodized aluminum tool, you will no longer have to worry about slicing the oil return tube O-rings or your fingers when installing these tight fitting seals. Simply insert the flanged end of the SR027 into the oil return tube, and slide the O-ring over the tapered end, sliding smoothly into place. No rips. No tears. No leaks.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SR027

您正在查看的产品与这些编号存在交叉引用关系

901/911/912/915/930 Precision shift coupler for Porsche 911



Our high quality, precisely engineered coupler ends sloppy shifting caused by worn (and even new!) factory couplers. Fabricated to exacting tolerances, the SR010 provides a precision feel and allows for accurate shifting. No more missed shifts during the heat of battle because of a sloppy factory coupler. The SR010 provides the precision and accuracy you demand when down shifting into that high-speed turn. No need to worry whether you are going to hit the wrong gear and over rev your engine. A quick bolt on replacement for the factory part. Shift with confidence, shift with precision. Available for 901/911/912/915/930.

Also available with our Shift Coupler Clamp (SR151) and/or shift bushing set (1 each of the Shift Tube Bushing and the Ball Cup Bushing).

For Installation Instructions please CLICK HERE

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SR010

您正在查看的产品与这些编号存在交叉引用关系

拆卸工具喷油器过滤器。

#北环赛道#

适合：
保时捷 911
保时捷 996
保时捷 924S
保时捷 944
保时捷 968


描述：
使用此专用工具，可以快速、干净、有效地拆卸喷油器的过滤器。此外，该工具的头部有一个定心注射器，可以使用它将新过滤器直接压入喷嘴而不会倾斜。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

5167

您正在查看的产品与这些编号存在交叉引用关系

Ring wench 36mm Generator nut. Laser Cut and zinc plated.



Fits:
Porsche 356 all
Porsche 912 >>1969

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

T265710002

您正在查看的产品与这些编号存在交叉引用关系

Shift coupler clamp for Porsche 911



CNC machined from aerospace alloy, our precision Shift Coupler Clamp ensures that your coupler stays where you set it. With extra clamping power ensured with our unique design, one-handed set-up, and anodized for great looks and protection, our Shift Coupler Clamp will provide that extra confidence you need.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SR151

您正在查看的产品与这些编号存在交叉引用关系

适用于保时捷 911 的火花塞孔修理套件

#斯托姆斯基#

911 头部的火花塞螺纹脱落通常意味着两种情况之一 - 维修不善或发动机故障无法正常维修。

到目前为止。

STOMSKI RACING 的新款 911 火花塞孔修复套件可让您精确地追踪受损头部的螺纹，或者在必要时通过安装 Time-Sert（或 Big-Sert）进行完全修复。我们新设计的数控夹具安装在两个气门盖螺栓上，当用随附的翼形螺钉锁定时，Time-Sert 铰刀、追踪器、丝锥和定位器可通过夹具的导管和定制丝锥驱动器精确对准 - 所有这些都在发动机仍在车内时进行。

有两种不同版本：

• SR130 与标准 M14x1.25 TimeSert 套件和插件（TS4412E 和 TS44111）一起使用；

• SR130BS 与 Big-Sert M14x1.25 超大插入套件和插入件 (TS5141E 和 TS51407) 一起使用。


我们还提供 Time-Sert/Big-Sert 14x1.25 套件和插件，以组成完整的包装。

Sprocket alignment tool for Porsche 911



Sprocket alignment on the 911 engine requires an accurate and repeatable ability to measure the offset of the sprockets and lay shaft. Simply using a straight edge and vernier calipers requires at least three hands and rarely produces precise measurements. Now, with the SR008, measuring sprocket alignment on the 911 engine has never been simpler, more accurate, or more repeatable. A precisely fabricated block of 6061 aluminum secures an oversized Starrett straight edge (included) to enable easy and exact measurements. No more guessing or settling for "close enough."
Includes custom caliper base, as well as thumb screws for mounting on all 911 engines including the 964.

Sprocket registration pin puller for Porsche 911



This unique tool allows you to easily pull the cam timing sprocket registration pin. No more yanking on the factory tool, hurting your fingers, or pulling the sprocket off the end of the cam shaft. Use this precisely machined slide hammer to delicately pull the pin.

TDC indicator with travel gauge for Porsche 911



For engines where you do not have to use our "dead-stop" TDC Indicator (SR022/23), use our easy to use, highly accurate TDC Indicator With Travel Gauge to measure the exact position of the piston. Precisely manufactured from 6061 Aluminum and hard-coated for extra wear resistance, these indicators include ASME/ANSI certified travel gauges for proven accuracy. Not recommended for use on the hemispherical heads on air-cooled 911s.

Available for either 10mm, 12mm, or 14mm spark plug holes.

Sold separately.

保时捷 911 的 TDC 指示器

#斯托姆斯基#

为了确保最高的计时精度，应检查所有发动机的真实 TDC，以确认皮带轮 TDC 标记相对于实际 TDC 的准确性。此工具拧入火花塞孔，并提供活塞相对于皮带轮/曲轴的位置的机械指示。通过旋转曲轴并接触/撞击活塞至死点 BTDC，然后以相反方向旋转发动机并再次接触/撞击活塞至死点 ATDC，在度盘、皮带轮或我们的 DigiDix-SR095 上记录两个测量值，您可以计算出纯 TDC。

适用于 12 毫米或 14 毫米火花塞孔。

分开售卖。

Through bolt o-ring installer for Porsche 911



Installing O-rings on the through bolts for a 911 engine case often slices the rings on the threads of the bolt, leading to ripped seals at best, or a leaky engine at worst. Use this cap to protect the O-ring and to insure a factory quality seal. Precisely machined from quality brass.

Stomski Racing SR024 Through bolt o-ring installer with sleeve for Porsche 911



Based on the factory P9511 tool, STOMSKI RACING's version of this tool incorporates a brass cap and a double-ended stainless steel sleeve to install the o-rings on the crankcase through-bolts of the 3.6 and later cases (but possibly can be used on some other 911 engines). By using the included brass cap to protect the delicate o-ring from getting cut on the threads of the bolt, you then use the "thin" end of the sleeve to slide the o-ring over the brass cap onto the shank of the through-bolt. Once the o-ring is clear of the threads, remove the SR024 brass cap and flip the SR024 stainless steel sleeve over and use the blunted end to securely and gently seat the o-ring in the recess on the 3.6 case.

Time-sert 火花塞 M14 x 1.25 深孔套件

Time-Sert 的 M14x1.25 深孔套件是我们的 SR130 的完美补充，包含阶梯丝锥、扳手、座刀和插入式驱动器。

图像上显示的插入件不包含在内，单独出售。

Time-Sert™ thread repair kit for SR065/SR067/SR068 for Porsche 911 / Boxster / 996 / 997



For exhaust port studs on 911, Boxster, 996/997 or GT3 heads where the threads have been pulled, or to recover from an already improper repair, we have developed this Time-Sert(tm) kit so you may use our SR065, SR067, SR068 or SR069 tools to insert a Time-Sert and save an otherwise ruined head. In addition to the standard Time-Sert(tm) parts (short P drill, counter-bore, tap, insert tool, and 5 short inserts), our kit also includes a full length P drill, two drill jigs/bushings to guide the P drill and tap in our SR065, SR067, or SR068 fixtures, 5 full length inserts, and 5 studs.

Time-Sert(tm) is a registered trademark of TIME FASTENER COMPANY

Timing chain strap / support for Porsche 911



When assembling the case halves on the 911 engine STOMSKI RACING's SR222 Timing Chain Strap will prove instrumental in supporting the chain to allow easier mating of the halves. Proper length, radius bend, tension, and quality steel insure that this tool will provide reliable and consistent support for all your engine builds.

Fits
• SR222 for all 911 engines

保时捷 911 变速箱选择杆固定板

#斯托姆斯基#

用于在调整和拧紧 901/911（SR260）或 915 变速箱（SR260A）上的换挡拨叉时固定换挡杆。

采用极其稳定的 Delrin 精密 CNC 加工而成，确保现在和多年使用后的准确性。

单独出售。