专业工具

气缸固定螺母，6 件套，适用于保时捷 911

#斯托姆斯基#

这些专门设计和制造的螺母可在重建期间将 911 气缸固定到位。螺母可轻松旋转曲柄并安装活塞/气缸，而不会使气缸滑出机壳。采用 2011 铝材精心制造，阳极氧化处理，可使用多年。每个螺母都配有特殊的 Delrin 衬垫，以保护您的气缸。

一套六件。

DigiDix™ Digital degree wheel cam timing system for Porsche all 911 and GT3 engines



A revolution in cam timing, STOMSKI RACING's DigiDix™ - Digital Degree Wheel - provides the most accurate, easy to use degree wheel ever. No more awkward setups, questionable readings, convoluted pointers, or imprecise measurements. With DigiDix™, simply bolt the sensor/adapter to the flywheel-end of the crankshaft and secure the torsion arm. Setup time is less than one minute. You are now ready to measure crank rotation to one tenth (.1) of one degree accuracy and repeatability.

DigiDix™ includes a 3 foot cable for easy reading anywhere on the engine and fits all 911 and GT3 engines (and others by special order). Storage case included.

STOMSKI RACING - "reinventing the wheel."

Stomski Racing SR124 Engine case splitter for Porsche 911



No more hammering, chiseling, swearing, heating, prying or praying to get an 911 engine case apart. STOMSKI RACING'S SR124 ELEGANTLY and GENTLY separates the engine case halves and not only shortens the process of engine tear-down, but it also protects what doubtlessly is an expensive asset- the engine case itself. The rare #s matching early 911S sand-cast aluminum case, or the impossible to find 911 GT3 RSR case, or the early magnesium case that seems so fragile, all can NOW be protected from the threat of the block of wood and lead hammer, or the torch, or the pry-bar and chisel.
SR124 includes a CNC precision machined aluminum platform that you bolt to four head studs (ideally over #2 or #5) using the included thumbscrews. An over-sized drive-screw (stainless steel) is then threaded through the platform to mate with a high-load bearing in our specially designed rod cap that presses against the wrist pin of #2 or #5 connecting rod that is at bottom-dead-center. As you slowly use a wrench or ratchet to tighten the drive-screw, the torque of the SR124 splitter is evenly distributed through the entire crankshaft, pressing against ALL 8 main bearings. Once the slack is taken up, only GENTLE effort on the drive screw is required to split even the most belligerent of cases.
The SR124 platform is designed to work on all Mezger 911s (2.0 through 997) and includes Delrin inserts/sleeves that protect the head studs from scratches or dings.

Head stud height setter for Porsche 911



Precisely set the height of head studs on all the 911 engines using this innovative tool. The Delrin insert protects the engine case from scratches or marring, while the adjustable three-piece anodized aluminium tubular construction provides complete flexibility for all engine setups, tools, and stud combinations.

For all 911s including GT3s.

适用于保时捷 911 的活塞/壳体喷射清洁剂

#斯托姆斯基#

最后，有一种简单的方法可以清洁和检查 911 机壳上的机壳/活塞喷射器。使用这种精密工具和压缩空气以及气枪强行打开喷射器并将其清理干净。此工具将机油槽两端密封，并允许空气通过喷射器孔口。无需拆卸/更换喷射器或猜测它们是否畅通。

阳极氧化铝/黄铜。

可配备或不配备气枪。

发动机支架用于发动机支架。

#北环赛道#

适合：
保时捷 356
保时捷 911 912 F/G
保时捷 930
保时捷 914
保时捷 964
保时捷 993
保时捷 996 turbo/GT2/GT3
保时捷 997 turbo/GT2/GT3
吸料管外径D=60mm

参考编号：
00072120100, 000.721.201.00, 000 721 201 00, P201

为了改装您的保时捷发动机，我们提供此发动机支架。法兰表面与悬臂一起连接到安装轴，可安全且同时轻松将发动机连接到滚动发动机支架上。或者，您可以使用发动机支架通过轴承座将发动机安装到工作台上。我们的计划中提供带和不带安装支架的所有经典保时捷的发动机支架。

注意：零件的颜色可能与所示颜色不同。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6898

您正在查看的产品与这些编号存在交叉引用关系

Exhaust head stud repair kit for Porsche Air-cooled 911's



Never lose sleep again over a bent or broken exhaust stud on a 911 engine. This new tool is a must for every 911 mechanic and will pay for itself the first time you use it. This is a quick and totally accurate tool to repair and replace broken studs without damaging the head, or worse, having to remove the engine. The SR065 fixture indexes off of the exhaust port (by using one of the various sized port bushings included), secures to the opposite stud, and allows you to drill out, tap, and replace the stud dead on, every time. Includes LH drill bits, tap with extension, drill jigs/guides, port bushings, and a sturdy storage case.

Now includes our SR065D drill guide.

Fits ALL of the 911 heads including the 993.

所有保时捷工厂工具包均包含此皮带轮固定扳手，在松开交流发电机螺母以更换三角皮带时与套筒扳手一起使用。

#北环赛道#

适合：
保时捷 911 2.0L / 2.2L / 2.4L 1969-74 年
保时捷 914-6 1970-72

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91172170200

您正在查看的产品与这些编号存在交叉引用关系

保时捷 911 专用 G50 精密换挡耦合器

#斯托姆斯基#

这是我们精密换挡耦合器的新版本，该耦合器是 G50 上的工厂橡胶衬套耦合器的螺栓替代品（与我们的 SR061 一起使用时无需焊接）。这个精密部件不需要钻孔或加工。SR060 可恢复清晰的换挡，使用寿命长达数年，并且每次都能提供准确的换挡。

固定螺钉单独出售。

Inner pulley holding wrench.



Fits:
Porsche 356 / 356A / 356B / 356C 1950-65
Porsche 911 / 912 1965-69

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

64457100203

您正在查看的产品与这些编号存在交叉引用关系

保时捷 911 输入轴法兰螺母套筒

STOMSKI RACING 版本的套筒用于拆卸/安装 901/911（SR252）或 915/930（SR252A）变速器上的输入轴法兰螺母，允许您使用输入轴的任一端通过将其安装到工厂工具上（例如从轴的一档端安装 P256）或通过使用安装在虎钳中的离合器盘来固定输入轴。

此外，与工厂式长管插座不同，SR252 和 SR252A 不太容易偏离输入轴的中心线。高品质冲击级插座和硬化钢焊接件，表面为黑色氧化物涂层。

• SR252 适用于 901/911/914 变速器。
• SR252A 适用于 915/930 变速器。

每个单独出售。

Leak-down / compression adapter for Porsche 911



You no longer need to fight or snake a flexible rubber hose blindly through the valve cover and into the cylinder head to hook up a compression or leak down gauge on the 911 engines (or other engines with remote spark plugs). Simply insert this unique tool into the spark plug hole of the cylinder head and attach your gauge. Precisely machined from high quality stainless steel or hard-coated aluminum.

Available in two sizes based on spark plug thread/diameter.

Sold separately.

Mechanical chain tensioners, Set of 2 for Porsche 911



Use these specially designed and fabricated mechanical tensioners to set cam timing, or as a bullet-proof alternative to pressure fed or hydraulic tensioners for racing.
CNC machined from 6061 aluminum and anodized for protection, these will become an integral part of your tool box or race engine. Complete with tensioning bolts, locking nuts, and spacers.

Comes in a set of TWO.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SR011

您正在查看的产品与这些编号存在交叉引用关系

保时捷 911 油冷却器测试仪

无需再为安装在 911 发动机上的机油冷却器猜测、疑惑或期盼。SR009 采用 6061 铝合金精密打造，让您轻松、快速、简便地检测冷却器是否泄漏。这款工具是所有冷却器（1965-1989 年）在重新安装前进行压力测试的必备工具。这款高品质工具经过阳极氧化处理，使用寿命长达多年，包含一个充满液体的压力表、美式嘴阀、密封件和配件。立即订购，避免冷却器泄漏带来的麻烦，也免去了为原本性能良好的发动机更换冷却器的麻烦。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SR009

您正在查看的产品与这些编号存在交叉引用关系

机油压力释放塞取出器 保时捷 911 / 964 / 993 / 996 / 997

泄压螺塞与其油道之间的公差非常小，哪怕是一点点污垢、腐蚀或毛刺都会导致螺塞在油道中冻结。磁铁的磁力很少足以克服卡住的螺塞，因此永远不要让它留在原位。
使用 STOMSKI RACING 的油压释放塞提取器可以轻松取出卡住的塞子，并确保油道清洁，旁路系统正常运行。

基于夹头的工具可轻松滑入卡住的插头的开口端，只需简单转动或旋转内部内六角螺钉一两圈即可展开工具，抓住插头，确保轻松取出。

阳极氧化铝。