后控制臂

Adjustable caster bushing kit.
1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 Boxster and Cayman -Front Only
Porsche 991 -Front Only

Caster Tuning
Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms (GT3 control arms or eccentric monoballs) to correct for un-intended caster change that is caused by the extended arms.

Caster is also a great tuning aid for adjusting out understeer. Our Caster Adjusters let you tune the caster you need.

Two eccentric mounting points increase range of adjustment by up to 25mm. Choose from the inner bore for minor caster adjustments or the outer bore for extreme adjustments.

Rear Weight Bias
For the rear suspension, our Caster Adjuster can reduce rear overhang and rear weight bias. Cars with aggressive rear camber actually draw the wheels forward, increasing rear weight bias. Use our Caster Adjuster to compensate and even over-compensate for less rear weight bias than stock

Maintain Proper Alignment
Our Caster Adjuster is solid aluminum to hold alignment settings precisely. Stock rubber bushings compress under load, allowing alignment to wander and making the car less predictable. Our solid design eliminates compression, improves precision and maintains geometry true.

Functional Design Built To Last
Available for factory type lower control arms (wishbones) front and rear, including stock type arms and GT3 arms

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180011

您正在查看的产品与这些编号存在交叉引用关系

Adjustable lower control arms (lower wishbone)



Fits
Porsche 986 Boxster - Front and Rear
Porsche 996, 997 - Front and Rear
Porsche 991 - Front Only
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 981 Boxster and Cayman - Front and Rear
Porsche 718 Boxster and Cayman - Front and Rear

Set of 2 x Adjustable lower control arms - 1 pair, required per axle

Elephant Racing adjustable lower control arms provide the camber, caster and precision you need. Length adjustable similar to the factory GT3 control arms, but without the need for shims.

Quick and Easy Adjustments – No need to keep a stock of shims on hand, length is easily adjusted by rotating the center hex head. Rotate clockwise to expand or counter-clockwise to contract the arm length.Adjustments can be made within minutes. No shims to mess with. Perfect setup to make quick changes for the track.

Widen Track – Use in combination with our camber plates on the front, or our adjustable length arms upper control arms on the rear to widen the track. This allows you to achieve a wider track without altering the scrub radius as happens when using wheel spacers.

Heim Joint – Our spherical bearings eliminate the deflection associated with rubber bushings. These bearings maintain stable suspension alignment, and improve feedback.

Fully Weather Sealed – Proper boots at both the ball joint and heim joint ends to keep water and contaminants out for extended life. These arms are suitable for extended road and track use.

Camber Adjustment – Extended range of adjustment lets you achieve aggressive camber. Or you can dial it back to get a factory street alignment on lowered cars.

Caster Adjustment – Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms to correct for un-intended caster change that is caused by the extended arms. Rotate the center puck and bolt down to secure the setting.

The arms are fully rebuildable with replaceable heim and ball joints.

On 996, 997, & 991 Cars:
Center puck can be also used as a wheelbase adjuster on the rear to draw the wheels back to improve weight distribution. It is a great tuning aid for adjusting out understeer

Litronic Bracket – This bracket is required for cars that are originally equipped with the litronic headlights. This adapter bracket attaches to the headlight angle sensor.


相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180001

您正在查看的产品与这些编号存在交叉引用关系

Rennline GT3 下控制臂 Litronics 支架。



适用：
保时捷 996 / 997 / 986 / 987 / 981 / 991

这款 Litronics 垫片套件包含您所需的一切，可将原厂 Litronics 系统与升级后的 GT3 控制臂配合使用。每套套件适用于前部或后部。
如果要在车辆的前后轴都安装 GT3 控制臂，则某些车辆需要前后轴套件。

Litronic Bracket for adjustable control arms.



Fits
Porsche 996 - Front & Rear with Litronic headlights
Porsche 997 - Front & Rear with Litronic headlights
Porsche 991 - Front & Rear with Litronic headlights

Porsche 986 - Front Only with Litronic headlights
Porsche 987 - Front Only with Litronic headlights
Porsche 981 - Front Only with Litronic headlights,

Price is for 1 and 2 Required per axle

This bracket is required for cars that are originally equipped with the Litronic headlights. This adapter bracket attaches to the headlight angle sensor.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180009

您正在查看的产品与这些编号存在交叉引用关系

Litronic可调控制臂支架。

#追踪大象#

合身
保时捷 987 - 带 Litronic 前大灯的尾部
保时捷 981 - 带 Litronic 前大灯的尾部

价格为每轴所需1个或2个的价格。

此支架适用于原厂配备Litronic前大灯的车辆。此适配器支架连接到前大灯角度传感器。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

218002

您正在查看的产品与这些编号存在交叉引用关系

下叉臂中央衬套拆卸和安装工具。

需要 1 个工具

#大象赛跑#

适合
保时捷 986 Boxster -前部和后部
保时捷 987 Boxster 和 Cayman -前部和后部
保时捷 996 -前部和后部
保时捷 997 -前部和后部
保时捷 981 Boxster 和 Cayman -仅前部
保时捷 991 -仅正面

简化 Monoball 产品和更换衬套的安装过程。

我们的两件式杯形和活塞工具可轻松取出和插入衬套，无需拆卸轮架或控制臂。无需使用车间压力机。这些工具的设计精确贴合衬套周长，可防止衬套意外损坏并确保正确安装。

我们有用于 LCA 中央衬套、后直立 LCA 衬套和后直立减震器支架衬套的工具。

996、997、986、987 和 981 上的前后控制臂
前下控制臂仅适用于 991

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2260019

您正在查看的产品与这些编号存在交叉引用关系

BBi Autosport front/rear lower control arm kit for Porsche 996/997/991/987/981 except GT4
Fits cars with and without PASM



Features :

•   Improved two piece 996 GT3 lower control arm design
•   Stronger than cast motorsport Cup arms
•   Allows proper camber adjustment
•   Uses GT3 shims to adjust camber & lower control arm length (sold separately)
•   High-strength steel alloy spherical bearings, completely serviceable unlike the motorsports arms
•   Sealed monoball inner bearing
•   Allows easy access to inner arm hardware
•   Includes adjustable thrust arm bushings to adjust caster and wheelbase
•   A must have for all track and race enthusiast
•   Each kit includes pair of 2 arms
•   Fits both front and rear axles
•   Compatible with all 996/997/991/987/981 models except GT4

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

BBILOWRCNTRL9697

您正在查看的产品与这些编号存在交叉引用关系

RSS Lower Control Arm Kit for Porsche Models .
Type: None Adjustable Thrust Arm Bushing



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Price: Set of Two Control Arms plus 2 x 1mm/2mm/3mm/7mm Shims.

RSS Tarmac Series Control Arms are manufactured from 6061 aerospace grade billet aluminum. This allows for a more uniform molecular structure
at every point of the arm over the cast motorsports arm giving the customer a more durable and inherently stronger part. Manufacturing from billet
aluminum rather than casting results in less impurities in the metal.

• Completely serviceable - for the extreme, repetitive track-day participant, our high-strength steel alloy spherical bearings (with a friction reducing /longevity increasing Teflon liner) can be replaced unlike the motorsports arm, in which case the customer will have to buy a new set of arms if the spherical bearings are worn.
Additionally, anodized surfaces and zinc-plated steel parts allow for better corrosion resistance against the elements.

• Adjustable suspension geometry - adjust dynamic camber values and roll center heights with our unique zinc-plated steel bushings.

• Solid monoball control arm ends offer a more responsive suspension over the factory one-piece rubber-injected control arm (also uses the same high
strength steel alloy spherical bearing found in our control arm monoball kit).

• Unique design provides more gusseting over the motorsports arms for added strength and aesthetically appealing looks.

Please Check Fitting Guide Before Ordering Click Here

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

357

您正在查看的产品与这些编号存在交叉引用关系

适用于保时捷车型的RSS下控制臂套件。
类型：无可调推力臂衬套



RSS Tarmac系列赛车下控制臂专为配备行程缩短的减震器/避震器（例如PASM或M030选装件）的降低车身车辆而设计。此外，如果车辆配备了高质量的改装或赛车级绞牙避震套件，例如Bilstein PSS10、KW V3或Ohlins等，也同样适用。

下控制臂与“基本型悬架”（长行程支柱/减震器）或“带有降低弹簧的基本型支柱/减震器”不兼容。
注意：请勿安装在配备基本型减震器/支柱的车辆上，否则当减震器/支柱完全伸展或完全下降时，可能会导致悬架卡滞，从而造成不安全的驾驶状况。

价格：一套两个控制臂，另加 2 个 1mm/2mm/3mm/7mm 垫片。

RSS Tarmac系列控制臂采用6061航空级铝坯制造，从而具有更均匀的分子结构。
与铸造的赛车用臂相比，该臂的每个连接点都经过特殊处理，为客户提供更耐用、更坚固的部件。采用坯料加工而成。
与铸造相比，铝制工艺可以减少金属中的杂质。

• 完全可维修 - 对于经常参加赛道日活动的极端用户而言，我们的高强度钢合金球形轴承（带有减少摩擦/延长使用寿命的特氟龙衬里）可以更换，而赛车运动臂则不同，如果球形轴承磨损，客户将不得不购买一套新的臂。
此外，阳极氧化表面和镀锌钢部件能够更好地抵抗各种环境因素的腐蚀。

• 可调悬架几何结构 - 使用我们独特的镀锌钢衬套调整动态外倾角值和侧倾中心高度。

• 实心单球头控制臂端头相比原厂一体式橡胶注塑控制臂（同样采用高阻尼材料），可提供更灵敏的悬架响应。
我们控制臂单球轴承套件中包含高强度钢合金球形轴承）。

• 独特的设计在赛车臂上增加了更多加强筋，以增强强度并提升美观度。

请在下单前查看尺码指南点击此处

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

358

您正在查看的产品与这些编号存在交叉引用关系

BBi Autosport 后狗骨臂组。



适合
991.1、991.2 Carrera 和 Carrera S
991.1 和 991.2 Carrera 4 以及 Carrera 4S
991.1 和 991.2 GTS
991.1 和 991.2 涡轮增压

产品描述：
BBi Autosport“狗骨”后臂组升级了工厂控制臂，采用机加工和阳极氧化装置，专门用于容纳球形轴承。

全套装置用橡胶衬套取代了悬架臂，恢复了悬架的控制力、稳定性和可预测性 - 与 RS 车型非常相似。

这些都是完全可以使用的部件。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

BBIDOGBONE991

您正在查看的产品与这些编号存在交叉引用关系

后直立轮架衬套工具。
每个应用需要 1 个工具

#大象赛跑#

适合
保时捷 991 - 后部
保时捷 991 Turbo - 后部

简化 Monoball 产品和更换衬套的安装过程。

我们的两件式杯形和活塞工具可轻松取出和插入衬套，无需拆卸轮架或控制臂。无需使用车间压力机。这些工具的设计精确贴合衬套周长，可防止衬套意外损坏并确保正确安装。

我们有用于 LCA 中央衬套、后直立 LCA 衬套和后直立减震器安装衬套的工具。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

226001

您正在查看的产品与这些编号存在交叉引用关系

ADJUSTABLE THRUST ARM BUSHING KIT (For vehicles equipped with Hydraulic Thrust Arm Bushings Only).
SET OF 4. FRONT AXLE ONLY



The RSS Adjustable Thrust Arm Bushing Kit will improve handling and response in 987. 997, 981, GT4, 991 GT3 variants, suspension systems and allows for additional caster adjustments. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.

AVAILABLE FOR ALL PORSCHE® 987,981, GT4, 997, 991 and 991 GT3, and 991 TURBO
NOT FOR 997 GT3/GT2

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

360

您正在查看的产品与这些编号存在交叉引用关系

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.



Fits
Porsche 991 GT3 OE Front Control Arms
Porsche 981 GT4 Front and Rear Control Arms
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,

Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing.
Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls. RSS Longer studs allow for more negative camber adjustment / gain vs. OE inner bushing. For camber shim kits see RSS Part # 308.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3-256

您正在查看的产品与这些编号存在交叉引用关系

保时捷车型下控制臂调整垫片



价格：一个对齐垫片

RSS 定位垫片专为配合工厂或售后市场的两件式赛车风格控制臂使用而设计。非常适合在安装过程中获得更多负外倾角和调整轮距。

垫片有多种尺寸，包括 1 毫米、2 毫米、3 毫米、5 毫米、7 毫米、10 毫米和 11 毫米。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

300

您正在查看的产品与这些编号存在交叉引用关系