后履带控制臂

Rear control arm bushing set.  Price is for 6 bushes. 
Designed to replace Porsche’s factory silent bloc in rear suspension link arms. Engineered for road use and built to OEM tolerances, this is a direct-fit, stock-spec solution for various Porsche 993.

Fits:
Porsche 993 1995-98 Stock Hardness

Replaces the rubber bushing on each of the rear 993 lower wishbone, camber control arm, and KT control arm. Each arm has 1 rubber bushing, for a total of 6 bushings per kit… enough to do one car.

Stock-hardness – Restores performance and ride quality to original.

Sport-Hardness – Similar to the 993 RS bushing, sport hardness rubber is about 25% firmer. Deflects less under cornering loads and thereby maintains alignment more precisely.

Features & Benefits

• OEM-equivalent rubber compound for a compliant, comfortable ride 
• Designed and manufactured in the EU with strict quality control 
• Backed by Prekom’s 2-year warranty  
• Straightforward installation; no modifications needed on stock link arms

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PR52004PKIT

您正在查看的产品与这些编号存在交叉引用关系

Rear upper control arm set
This OE Match rear upper control arm kit is a complete suspension service set designed for Porsche 911 (993) models. The kit includes two rear upper control arms together with lock nuts and the eccentric alignment hardware required for installation, allowing proper mounting and rear suspension alignment adjustment. The control arms connect the rear wheel carrier to the chassis, forming part of the Porsche 993 multi-link rear suspension system and helping maintain precise wheel alignment and handling stability.
SET OF 2  control arms with bolts, nuts and washers

Fits:
Porsche 993 1994 - 1997 

Diagram ref no 5, 

Kit Includes
  2 × OE Match Rear Upper Control Arm  with Lock nut – 99333104703 + 99908444909
  2 × OE Match Eccentric Bolt – 99733121702
  2 × OE Match Eccentric Washer – PAF007648
  2 × OE Match Locknut – 99908444501

The rear upper control arm (often referred to as the rear forward suspension link) is a key component of the multi-link rear suspension used in Porsche 993 models. It links the rear wheel carrier to the chassis and allows controlled suspension movement while maintaining accurate wheel geometry.

This OE Match kit includes two control arms (left and right) along with the correct alignment hardware. The eccentric bolts and washers allow technicians to precisely adjust rear wheel alignment angles such as camber and toe, ensuring optimal handling and tyre wear.

By including the mounting hardware, the kit provides a complete installation solution suitable for suspension refurbishment or restoration work.

Rear suspension arms and their ball joints are exposed to constant load, road impacts and suspension movement. Over time they can develop play or wear, which may lead to poor handling, alignment drift or uneven tyre wear. Replacing both control arms together with new alignment hardware restores the correct suspension geometry and ensures reliable rear-axle stability.

When to Replace. Consider replacing the rear upper control arms if you notice:
•  Clunking noises from the rear suspension
•  Excessive movement or play in suspension joints
•  Uneven rear tyre wear
•  Alignment adjustments no longer holding correctly

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99333104703

您正在查看的产品与这些编号存在交叉引用关系

后束、外倾角和运动控制臂。


套件包含：
（4）上控制臂，（2）前束控制臂

適用於:
保时捷 993

如果您对 993、996、997、Cayman 或 Boxster 的操控性非常在意，则应使用可调控制臂连杆升级后悬架。工厂连杆有两个主要缺点：
1) 您无法降低汽车的重量并保持适当的悬架几何形状。工厂连杆会产生过多的内倾角，无法调整，从而造成操控问题和轮胎过度磨损。
2) 工厂连杆有橡胶衬套，这使得操控不精确，特别是在悬架负载最高的性能驾驶中。

Rennline 可调控制臂连杆解决了这两个问题。由 6061 铝制成，采用螺丝扣设计，可以根据需要延长或缩短每个臂，以恢复降低的保时捷的正确悬架几何形状。FK 特氟龙衬里的杆端轴承确保精确操控并锁定汽车的定位设置，确保在任何条件下可预测转弯。Rennline 臂配有完成工作所需的所有螺栓和机加工衬套。橡胶靴不包含在内，但单独提供。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

S7273741012415

您正在查看的产品与这些编号存在交叉引用关系