Targa

Targa top restoration outer cover,  for your Porsche 911 from 1964 through 1993.
The outer cover does not include any hardware or weatherstrips. However these can be re-used in most cases.
Requires a specialist to fit this product.
Fits:
Porsche 912
Porsche 911 1965 - 1989
Porsche 964 1989 - 1994
Delivery Time is Normally 10 - 14 days on this product
This cover renews the outer finish of the Targa roof - helping restore a clean, factory-style appearance while providing a refreshed outer layer that supports weather protection and reduces wind/water issues associated with aged, split, or shrinking original coverings.
•  Replaces the worn or damaged outer skin of the Targa roof panel
•  Helps maintain a weather-resistant exterior surface
•  Restores the correct look/texture for a tidy, OE-style roof finish
Over time, Targa outer skins can fade, crack, shrink, lift at edges, or lose their seal, affecting both appearance and weather resistance. Replacing the outer cover is a key step in a proper Targa roof restoration, helping bring back the correct finish and improving overall roof integrity.
When to replace:
•  Visible cracking, splitting, or lifting of the outer skin
•  Persistent wind noise or water issues traced to roof covering condition
•  Faded, scuffed, or poorly repaired outer surface
•  During a full Targa top restoration/retrim

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90156503541

The product you are viewing cross references to these numbers

Targa roof handle - for  left or right side
Fits: 
Porsche 911 1972-85 Targa
Diagram ref no 15

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156507541

The product you are viewing cross references to these numbers

Targa top roof handle - fits left right hand side
Fits: 
Porsche 911 1972-85 Targa
Diagram ref no 15

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156507541

The product you are viewing cross references to these numbers

Targa Top Lateral Seals (Over Door Glass)

OE Match replacement Targa top lateral rubber seals. These seals are fitted along the left and right sides of the removable Targa roof panel, directly above the door glass.

Fits:

• Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
• Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
• Porsche 911 1978-1983 3.0L / SC
• Porsche 911 1984-1986 3.2L
• Porsche 911 1987-1989 3.2L G50
• Porsche 911 1978-1989 3.3L Turbo (930)

Diagram Ref: 45

Designed to replicate the original sealing arrangement, they help create a weather-resistant barrier between the Targa roof and the upper edges of the side windows, reducing water ingress, wind noise and unwanted draughts.

Ideal for replacing hardened, cracked, flattened or damaged original seals during routine Targa roof maintenance, roof refurbishment or a complete classic Porsche restoration.

What Do Targa Top Lateral Seals Do?

The lateral seals run along the sides of the removable Targa roof panel, creating a protective seal against the upper edges of the door glass when the windows are closed.

Their primary functions include:

Helping prevent rainwater entering around the top of the door glass Reducing wind noise at higher road speeds Preventing unwanted draughts entering the passenger compartment Providing a flexible contact surface between the roof and window glass Helping maintain the correct Targa roof sealing arrangement Supporting comfortable, weather-resistant driving

Correctly fitted lateral seals are particularly important on Targa models because the removable roof and frameless door glass must align correctly to achieve an effective seal.

Why Do Targa Lateral Seals Fail?

Original Targa roof seals are exposed to sunlight, temperature changes, moisture and repeated compression from the door glass.

Over time, the rubber can deteriorate and lose its ability to form an effective seal.

Common causes of failure include:

Rubber hardening through age Cracking or splitting Flattening from prolonged compression Shrinkage or distortion Exposure to UV light and changing temperatures Damage during roof removal or installation Incorrect door glass adjustment Poor roof alignment or worn roof components

As the rubber deteriorates, gaps may develop between the window glass and the Targa roof, allowing water and wind noise into the vehicle.

When Should Targa Lateral Seals Be Replaced?

Replacement is recommended whenever the original seals show signs of damage or no longer provide an effective seal.

Typical indications include:

Water entering above the side windows Excessive wind noise around the Targa roof Draughts entering at the top of the door glass Hardened, cracked or split rubber Flattened or permanently compressed sealing surfaces Visible gaps between the roof seal and window glass Loose or distorted sections of weatherstrip Deterioration discovered during Targa roof refurbishment

Replacing worn lateral seals can help restore the original weather protection of the vehicle, provided the roof and door glass are correctly adjusted.

Fitment should be confirmed against the original roof seal profile and vehicle specification, particularly where a replacement or refurbished Targa roof has previously been installed.

Checks During Replacement

When replacing the Targa top lateral seals, inspect the complete roof sealing system to ensure the new rubber provides an effective fit.

Check the front and rear Targa roof seals for deterioration, and inspect the roof frame, retaining components and mounting channels for damage.

The door glass should also be checked for correct height, angle and alignment. Incorrect window adjustment can prevent even a new lateral seal from making proper contact.

Ensure the roof panel sits correctly against the windscreen frame and rear Targa bar before assessing the sealing contact.

Where necessary, adjust the roof and door glass according to the Porsche workshop procedure.

Porsche 911 Targa Roof Lateral Seals & Door Glass Weatherstrips

Maintaining the Targa roof sealing system is essential for protecting the interior of classic Porsche 911 Targa models against water ingress, wind noise and unwanted draughts.

Unlike a fixed-roof Coupé, the Porsche 911 Targa uses a removable roof panel with flexible rubber seals along its front, rear and lateral edges. The side seals are particularly important because they must provide consistent contact with the frameless door glass.

Over time, the original lateral weatherstrips can become hardened, flattened, cracked or distorted, reducing their effectiveness and allowing moisture or wind noise to enter the passenger compartment.

Replacing worn lateral seals helps restore the original roof sealing arrangement, improves contact with the door glass and contributes to a more comfortable driving experience.

These seals are suitable for routine maintenance, Targa roof refurbishment, water leak repairs and complete classic Porsche restoration projects.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

9115652

The product you are viewing cross references to these numbers

Targa top lateral / horizontal seal, Fits over door drop glass complete with internal metal insert.
Fits:
Porsche 911 1970-89
Diagram Ref: 45

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

9115652

The product you are viewing cross references to these numbers

Targa Top lateral / horizontal Seal, Fits over door drop glass complete with internal metal insert.
The Targa side roof seal is designed to restore proper weather sealing along the side edge of the removable Targa roof panel on classic Porsche 911 models. This precision-moulded rubber seal fits between the Targa top and the side window frame, creating a tight barrier that prevents wind, water, and road noise from entering the cabin.
Fits:
Porsche 911 1970 - 1989
Diagram ref no 45
Old Targa roof seals commonly fail due to UV exposure, compression set, and age. A damaged seal can lead to:
• Water ingress into interior trim and carpets
• Excessive wind noise or whistling
• Poor window alignment and rattles
• Reduced roof stability and overall cabin comfort.
Replacing the seal restores a tight, clean Targa-top closure and protects the interior from the elements.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

9115652

The product you are viewing cross references to these numbers

Targa soft top locking pin, Front.
2 pieces needed per car. Sold each.
It is a good idea to replace this plate when purchasing new location pegs (91156507440)
Fits:
Porsche 911 Targa 2.0-3.3 07/66-07/89
Porsche 964 Targa 3.6 12/88-09/93
Click 'Zoom in' for large parts diagram.
Diagram ref no 9

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90156520340

The product you are viewing cross references to these numbers

Targa soft top locking pin, Front.
2 pieces needed per car. Sold each.
It is a good idea to replace this plate when purchasing new location pegs (91156507440)
Fits:
Porsche 911 Targa 2.0-3.3 07/66-07/89
Porsche 964 Targa 3.6 12/88-09/93
Click 'Zoom in' for large parts diagram.
Diagram ref no 11

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90156520340

The product you are viewing cross references to these numbers

Transparent Targa Roof for Porsche 911 Targa (1967- up to Summer 1985) Carbon Version.
In the period from 1967- up to Summer 1985, Porsche produced all Targas with claw locks. Unfortunately, the claw lock or the thin sheet metal in which it engages is not permanently dimensionally stable, which means that damage can occur. We solve this problem with an adapter set that converts the claw closure of all Porsche Targa models from 1967- up to Summer 1985 to a roller closure.
This not only protects the windscreen frame from deformation and makes it easier to fit the GTS-TOP using the roller lock, but also prevents water from penetrating the tubular frame.
The GTS-Top is made of innovative and advanced materials, for example: extremely lightweight and highly robust carbon fiber (CFRP) for the frame, with Makrolon glass, hard anti-scratch coating, stainless steel fasteners with Teflon bushings and modern EPDM seals. It is 2kg lighter than the already light original one.
Specifications:
Carbon-Composite High-Tech Framework
Stainless steel roll latches and 5-pins with Teflon bushing
High-Tech nano coated Makrolon window (Antistatic and Anti-scratch coating)
Exterior:
Colour of window tint : Green
Interior:
Frame: matt-black structure paint
(Optional: Visible Carbon, Alcantara, Leather, or Painted)
Fits
Porsche 911 1967- up to Summer 1985
**Please note the bag is not included cost is £175.00 extra.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

V2CMA12

The product you are viewing cross references to these numbers