后控制臂

Adjustable caster arms with anti-dive and anti-squat.



Fits
Porsche 986 Boxster - Front Only
Porsche 987 Boxster and Cayman - Front Only
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear

Set of 2 x Adjustable caster arms - 1 pair, required per axle

Elephant Racing caster arms provide adjustable caster and anti-dive ability when used on the front, and adjustable wheel base, weight distribution, and anti-squat when used on the rear.

Front Suspension

Threaded double-adjuster makes it easy to extend or shorten the arm.

This makes for easy caster adjustment – an important adjustment the factory left out. A must-have for cars with GT3 style extendable style lower control arms to correct for un-intended caster increase that is caused by the extended LCAs.

Anti-dive behavior can also be adjusted. Lowering the front of the arm using the provided spacers reduces front dive under braking. Adjustable in 2mm increments.

Rear Suspension

Adjustable Caster Arms can reduce rear overhang and rear weight bias. A must-have for cars with GT3 style extendable style lower control arms. Adjust the length of the caster arms to correct the position of the rear wheels that have been drawn forward by aggressive camber settings. Even over-compensate for less rear weight bias than stock.

With the heavy mass of the engine cantilevered behind the rear axle, even small changes in wheel base make significant changes in weight distribution. Shortening the overhang reduces the famous 911 "pendulum" effect in corners.

Anti-squat behavior can also be adjusted. Raising the front of the caster arm using the provided spacers reduces rear squat under acceleration. Adjustable in 2mm increments.

Fully weather sealed> – Proper boots at the heim joint keep water and contaminant out for extended life.

If not using Adjustable Lower Control Arms

1999-2012 996, Boxster, Cayman, & GT3 Front: Bolt on if replacing the lower control arm central bushing with 2290022 / 2290014 rubber bushings, or our 2180011 camber adjusters.

1999-2012 996, 997 & GT3 Rear: Straight bolt on.

2006-2018 997, Boxster, Cayman, & 991 Front: Requires fitment of our part number 2290022 or 2290014 LCA central bushings or 2180011 solid caster bushing kit

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180005

您正在查看的产品与这些编号存在交叉引用关系

Adjustable caster bushing kit.
1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 Boxster and Cayman -Front Only
Porsche 991 -Front Only

Caster Tuning
Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms (GT3 control arms or eccentric monoballs) to correct for un-intended caster change that is caused by the extended arms.

Caster is also a great tuning aid for adjusting out understeer. Our Caster Adjusters let you tune the caster you need.

Two eccentric mounting points increase range of adjustment by up to 25mm. Choose from the inner bore for minor caster adjustments or the outer bore for extreme adjustments.

Rear Weight Bias
For the rear suspension, our Caster Adjuster can reduce rear overhang and rear weight bias. Cars with aggressive rear camber actually draw the wheels forward, increasing rear weight bias. Use our Caster Adjuster to compensate and even over-compensate for less rear weight bias than stock

Maintain Proper Alignment
Our Caster Adjuster is solid aluminum to hold alignment settings precisely. Stock rubber bushings compress under load, allowing alignment to wander and making the car less predictable. Our solid design eliminates compression, improves precision and maintains geometry true.

Functional Design Built To Last
Available for factory type lower control arms (wishbones) front and rear, including stock type arms and GT3 arms

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180011

您正在查看的产品与这些编号存在交叉引用关系

Adjustable lower control arms (lower wishbone)



Fits
Porsche 986 Boxster - Front and Rear
Porsche 996, 997 - Front and Rear
Porsche 991 - Front Only
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 981 Boxster and Cayman - Front and Rear
Porsche 718 Boxster and Cayman - Front and Rear

Set of 2 x Adjustable lower control arms - 1 pair, required per axle

Elephant Racing adjustable lower control arms provide the camber, caster and precision you need. Length adjustable similar to the factory GT3 control arms, but without the need for shims.

Quick and Easy Adjustments – No need to keep a stock of shims on hand, length is easily adjusted by rotating the center hex head. Rotate clockwise to expand or counter-clockwise to contract the arm length.Adjustments can be made within minutes. No shims to mess with. Perfect setup to make quick changes for the track.

Widen Track – Use in combination with our camber plates on the front, or our adjustable length arms upper control arms on the rear to widen the track. This allows you to achieve a wider track without altering the scrub radius as happens when using wheel spacers.

Heim Joint – Our spherical bearings eliminate the deflection associated with rubber bushings. These bearings maintain stable suspension alignment, and improve feedback.

Fully Weather Sealed – Proper boots at both the ball joint and heim joint ends to keep water and contaminants out for extended life. These arms are suitable for extended road and track use.

Camber Adjustment – Extended range of adjustment lets you achieve aggressive camber. Or you can dial it back to get a factory street alignment on lowered cars.

Caster Adjustment – Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms to correct for un-intended caster change that is caused by the extended arms. Rotate the center puck and bolt down to secure the setting.

The arms are fully rebuildable with replaceable heim and ball joints.

On 996, 997, & 991 Cars:
Center puck can be also used as a wheelbase adjuster on the rear to draw the wheels back to improve weight distribution. It is a great tuning aid for adjusting out understeer

Litronic Bracket – This bracket is required for cars that are originally equipped with the litronic headlights. This adapter bracket attaches to the headlight angle sensor.


相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180001

您正在查看的产品与这些编号存在交叉引用关系

BBi Autosport adjustable rear toe kit



Fits
Porsche 981 Boxster
Porsche 981 Cayman

Features :

•   Provides additional rear toe adjustment
•   OEM link is non-adjustable and eccentric bolt provides limited adjustment range, causing excessive tire wear and handling issues.
•   Helps maintain proper rear end suspension geometry
•   Fits rear axle
•   Each Kit Includes Pair of 2 Links

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

BBITOE981

您正在查看的产品与这些编号存在交叉引用关系

带有可调衬套的跟踪控制臂。

#罗勒#

两个衬套均采用黑色 95A 材料以实现最佳性能，并配有偏置外套管和 CNC 加工内套，可在车上调整主销后倾角和外倾角，从而快速轻松地优化车轮定位。（不包括工具或扳手）这些臂具有悬架几何调整功能，主销后倾角最多可增加 0.4°，外倾角调整范围为 +/- 0.75°

OEM 零件编号： 98133105301、99733104180、99634105319

適用於:

正面
保时捷 997 GT2、GT3 和 GT3RS
保时捷 986 Boxster（1997-2004）
保时捷 996（1997-2005）

后部
保时捷 997 GT2、GT3 和 GT3RS
保时捷 997 配备涡轮增压
保时捷 718 Boxster/Cayman
保时捷 981 Boxster/Cayman
保时捷 986 Boxster（1997-2004）
保时捷 987 Boxster（2005-2012）
保时捷 987C Cayman（2005 - 2012 年）
保时捷 996（1997-2005）

请注意：您将需要 997 个前叉臂来容纳可调节衬套，因为它们比标准衬套更宽。
当您将此商品添加到购物篮时，系统将提示您也需要添加必填产品。

提供可调节和不可调节衬套选项，以适应不同的驾驶和性能要求。

请点击‘放大’查看图表（第 21 号）

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3602409961G

您正在查看的产品与这些编号存在交叉引用关系

GT3 Adjustable outer lower control arms – 2 Piece,
with adjustable caster puck.



Fits:
Porsche 991 Front Only (Does Not Fit 991 GT3)
Porsche 992 Front Only (Does Not Fit 992 GT3)
Porsche 981 Front And Rear


GT3 Lower Control Arms (LCA)

992 GT3 cars are equipped with a special front GT3 control arm that is two-piece and length-adjustable by fitting shims between the halves. The changeable length allows for aggressive camber settings and track width adjustment, increasing cornering grip and performance.
Unfortunately the stock 992 GT3 control arm cannot be fit to a non-GT3 992 because the ball joint end is completely different.
That’s why we created these GT3 type front lower control arms to fit the 992 C2, C4 and Turbo cars.
Our GT3 ERX LCAs for the 922 provides the same type front camber and track width adjustment for non-GT3 992 cars.

The GT3 ERX lower control arm is a system built up of three component parts, each ordered separately:
– GT3 ERX adjustable outer lower control arm
– GT3 adjustable inner lower control arm
– GT3 lower control arms shims (various thicknesses, stackable)

GT3 ERX Front Outer Lower Control Arms

Elephant Racing has developed an upgraded GT3 type front lower control arm for the non-GT3 992 cars. Our GT3 type arms have the correct ball joint style for fitment to 992 C2, C4 and Turbo cars. They do not fit 992 GT3 cars.

Like the factory lower control arms, the Elephant Racing outer arm has an integrated ball joint that is weather sealed. Unlike the factory lower control arms, the ball joint in the Elephant Racing arms is rebuildable and we offer the rebuild kit allowing you to renew the arm when needed.

The GT3 ERX LCAs have features to accept the factory height sensor and air deflectors.

The outer arms are sold as a left and right side pair, to be combined with our GT3 inner lower control arms – orderable separately.

These can be paired with a choice of GT3 lower control arms inner:
– Elephant Racing GT3 lower control arm inner rubber bushing
– Elephant Racing GT3 lower control arm inner spherical bearing


相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180044

您正在查看的产品与这些编号存在交叉引用关系

Rennline GT3 下控制臂 Litronics 支架。



适用：
保时捷 996 / 997 / 986 / 987 / 981 / 991

这款 Litronics 垫片套件包含您所需的一切，可将原厂 Litronics 系统与升级后的 GT3 控制臂配合使用。每套套件适用于前部或后部。
如果要在车辆的前后轴都安装 GT3 控制臂，则某些车辆需要前后轴套件。

Litronic Bracket for adjustable control arms.



Fits
Porsche 996 - Front & Rear with Litronic headlights
Porsche 997 - Front & Rear with Litronic headlights
Porsche 991 - Front & Rear with Litronic headlights

Porsche 986 - Front Only with Litronic headlights
Porsche 987 - Front Only with Litronic headlights
Porsche 981 - Front Only with Litronic headlights,

Price is for 1 and 2 Required per axle

This bracket is required for cars that are originally equipped with the Litronic headlights. This adapter bracket attaches to the headlight angle sensor.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180009

您正在查看的产品与这些编号存在交叉引用关系

Litronic可调控制臂支架。

#追踪大象#

合身
保时捷 987 - 带 Litronic 前大灯的尾部
保时捷 981 - 带 Litronic 前大灯的尾部

价格为每轴所需1个或2个的价格。

此支架适用于原厂配备Litronic前大灯的车辆。此适配器支架连接到前大灯角度传感器。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

218002

您正在查看的产品与这些编号存在交叉引用关系

下叉臂中央衬套拆卸和安装工具。

需要 1 个工具

#大象赛跑#

适合
保时捷 986 Boxster -前部和后部
保时捷 987 Boxster 和 Cayman -前部和后部
保时捷 996 -前部和后部
保时捷 997 -前部和后部
保时捷 981 Boxster 和 Cayman -仅前部
保时捷 991 -仅正面

简化 Monoball 产品和更换衬套的安装过程。

我们的两件式杯形和活塞工具可轻松取出和插入衬套，无需拆卸轮架或控制臂。无需使用车间压力机。这些工具的设计精确贴合衬套周长，可防止衬套意外损坏并确保正确安装。

我们有用于 LCA 中央衬套、后直立 LCA 衬套和后直立减震器支架衬套的工具。

996、997、986、987 和 981 上的前后控制臂
前下控制臂仅适用于 991

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2260019

您正在查看的产品与这些编号存在交叉引用关系

BBi Autosport front/rear lower control arm kit for Porsche 996/997/991/987/981 except GT4
Fits cars with and without PASM



Features :

•   Improved two piece 996 GT3 lower control arm design
•   Stronger than cast motorsport Cup arms
•   Allows proper camber adjustment
•   Uses GT3 shims to adjust camber & lower control arm length (sold separately)
•   High-strength steel alloy spherical bearings, completely serviceable unlike the motorsports arms
•   Sealed monoball inner bearing
•   Allows easy access to inner arm hardware
•   Includes adjustable thrust arm bushings to adjust caster and wheelbase
•   A must have for all track and race enthusiast
•   Each kit includes pair of 2 arms
•   Fits both front and rear axles
•   Compatible with all 996/997/991/987/981 models except GT4

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

BBILOWRCNTRL9697

您正在查看的产品与这些编号存在交叉引用关系

RSS Lower Control Arm Kit for Porsche Models .
Type: None Adjustable Thrust Arm Bushing



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Price: Set of Two Control Arms plus 2 x 1mm/2mm/3mm/7mm Shims.

RSS Tarmac Series Control Arms are manufactured from 6061 aerospace grade billet aluminum. This allows for a more uniform molecular structure
at every point of the arm over the cast motorsports arm giving the customer a more durable and inherently stronger part. Manufacturing from billet
aluminum rather than casting results in less impurities in the metal.

• Completely serviceable - for the extreme, repetitive track-day participant, our high-strength steel alloy spherical bearings (with a friction reducing /longevity increasing Teflon liner) can be replaced unlike the motorsports arm, in which case the customer will have to buy a new set of arms if the spherical bearings are worn.
Additionally, anodized surfaces and zinc-plated steel parts allow for better corrosion resistance against the elements.

• Adjustable suspension geometry - adjust dynamic camber values and roll center heights with our unique zinc-plated steel bushings.

• Solid monoball control arm ends offer a more responsive suspension over the factory one-piece rubber-injected control arm (also uses the same high
strength steel alloy spherical bearing found in our control arm monoball kit).

• Unique design provides more gusseting over the motorsports arms for added strength and aesthetically appealing looks.

Please Check Fitting Guide Before Ordering Click Here

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

357

您正在查看的产品与这些编号存在交叉引用关系

适用于保时捷车型的RSS下控制臂套件。
类型：无可调推力臂衬套



RSS Tarmac系列赛车下控制臂专为配备行程缩短的减震器/避震器（例如PASM或M030选装件）的降低车身车辆而设计。此外，如果车辆配备了高质量的改装或赛车级绞牙避震套件，例如Bilstein PSS10、KW V3或Ohlins等，也同样适用。

下控制臂与“基本型悬架”（长行程支柱/减震器）或“带有降低弹簧的基本型支柱/减震器”不兼容。
注意：请勿安装在配备基本型减震器/支柱的车辆上，否则当减震器/支柱完全伸展或完全下降时，可能会导致悬架卡滞，从而造成不安全的驾驶状况。

价格：一套两个控制臂，另加 2 个 1mm/2mm/3mm/7mm 垫片。

RSS Tarmac系列控制臂采用6061航空级铝坯制造，从而具有更均匀的分子结构。
与铸造的赛车用臂相比，该臂的每个连接点都经过特殊处理，为客户提供更耐用、更坚固的部件。采用坯料加工而成。
与铸造相比，铝制工艺可以减少金属中的杂质。

• 完全可维修 - 对于经常参加赛道日活动的极端用户而言，我们的高强度钢合金球形轴承（带有减少摩擦/延长使用寿命的特氟龙衬里）可以更换，而赛车运动臂则不同，如果球形轴承磨损，客户将不得不购买一套新的臂。
此外，阳极氧化表面和镀锌钢部件能够更好地抵抗各种环境因素的腐蚀。

• 可调悬架几何结构 - 使用我们独特的镀锌钢衬套调整动态外倾角值和侧倾中心高度。

• 实心单球头控制臂端头相比原厂一体式橡胶注塑控制臂（同样采用高阻尼材料），可提供更灵敏的悬架响应。
我们控制臂单球轴承套件中包含高强度钢合金球形轴承）。

• 独特的设计在赛车臂上增加了更多加强筋，以增强强度并提升美观度。

请在下单前查看尺码指南点击此处

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

358

您正在查看的产品与这些编号存在交叉引用关系